E5 series cartridges are composed of advanced polypropylene membrane and supporting layer, with high flux, high precision and low pressure drop, it is an economical choice for pre-filtration.
Applications
Buffer prefiltration
Pre-filtration of sterile raw materials
Pre-filtration of water for pharmaceutical use
Blood product prefiltration
Product features
No fiber shedding
Gradient pore size with extremely high dirt holding capacity
No foreign substances such as adhesives
Features broad chemical resistance
Flow curves
MoC | |
Membrane material | Polypropylene |
Center rod/housing/end cap | Polypropylene |
Supporting layer | Polypropylene |
Sealing ring | Refer to ordering information |
Surface area | 0.4m2/10 inch |
Working condition | |
Max. working temperature | 80℃(0.173MPa) |
Max. working pressure difference | 0.5MPa(25℃) |
0.25MPa(80℃) | |
Autoclave | 121℃ (30min,5 times) |
Biosafety | |
Endotoxin | <0.25EU/ml |
Biosafety | Meets USP<87> and USP<88> biosafety requirements |
Product number key of high precision polypropylene disc filter
Housing model | Membrane material | Pore size (μm) | Type | Length (inch) | Inlet/Outlet | Sterilization |
DS=Disc filter | E5=Polypropylene | 091=0.1 092=0.2 094=0.45 096=0.65 098=0.85 001=1.0 003=3.0 005=5.0 010=10 020=20 030=30 | F=Pharmaceutical grade | 02=2 | 2H=1/4" HB | G=Gamma irradiated, re-autoclaving is no longer tolerated F=Tolerate gamma irradiation only, but not yet irradiated None=Tolerant autoclaving only, but not yet autoclaved |
Product number key of high precision polypropylene CA series capsule filter
Housing model | Membrane material | Pore size (μm) | Type | Length (inch) | Structure type | Inlet | Outlet | Sealing ring material | Sterilization |
CA=Diameter 110 capsule filter | E5=Polypropylene | 091=0.1 092=0.2 094=0.45 096=0.65 098=0.85 001=1.0 003=3.0 005=5.0 010=10 020=20 030=30 | F=Pharmaceutical grade | 05=5 10=10 20=20 30=30 | L=Up-in & down-out | H=1"-1.5" TC | H=1"-1.5" TC F=1/2" HB | S=Silicone E=EPDM V=Fluorelastomer | G=Gamma irradiated, re-autoclaving is no longer tolerated F=Tolerate gamma irradiation only, but not yet irradiated None=Tolerant autoclaving only, but not yet autoclaved |
Technical parameter of high precision polypropylene CA series capsule filter
Material | Series | Size code | Single/dual layer | Surface area(㎡)≥ | Pure water flow 0.2 μm ΔP=0.01MPa |
Polypropylene | CA capsule filter | F05 | Single layer | 0.2 | ≥5L/min |
F10 | Single layer | 0.4 | ≥10L/min | ||
F20 | Single layer | 0.8 | ≥20L/min | ||
F30 | Single layer | 1.2 | ≥30L/min |
Product number key of high precision polypropylene CB series capsule filter
Housing model | Membrane material | Pore size (μm) | Type | Length (inch) | Structure type | Inlet | Outlet | Sterilization |
CB=Diameter 70 capsule filter | E5=Polypropylene | 091=0.1 092=0.2 094=0.45 096=0.65 098=0.85 001=1.0 003=3.0 005=5.0 010=10 020=20 030=30 | F= Pharmaceutical grade | H1=1(minor Dia.) 01=1(wide Dia.) 1H=1.5 02=2.5 05=5 | L=Up-in & down-out | A=1/4"NPT D=1/4" HB E=3/8" HB F=1/2" HB G=1/2" TC H=1-1.5" TC J=1/4-1/2" HB | A=1/4"NPT D=1/4" HB E=3/8" HB F=1/2" HB G=1/2" TC H=1-1.5" TC J=1/4-1/2" HB | G=Gamma irradiated, re-autoclaving is no longer tolerated F=Tolerate gamma irradiation only, but not yet irradiated None=Tolerant autoclaving only, but not yet autoclaved |
Technical parameter of high precision polypropylene CB series capsule filter
Material | Series | Size code | Single/dual layer | Surface area(㎡)≥ | Pure water flow 0.2 μm ΔP=0.01MPa |
Polypropylene | CB capsule filter | FH1 | Single layer | 0.01 | ≥0.25L/min |
F01 | Single layer | 0.02 | ≥0.5L/min | ||
F1H | Single layer | 0.04 | ≥1L/min | ||
F02 | Single layer | 0.08 | ≥2L/min | ||
F05 | Single layer | 0.15 | ≥3.75L/min |
Product number key of high precision polypropylene cartridge
Membrane material | Pore size (μm) | Type | Length (inch) | Connection type | Sealing type | Sealing ring material |
E5=Polypropylene | 091=0.1 092=0.2 094=0.45 096=0.65 098=0.85 001=1.0 003=3.0 005=5.0 010=10 020=20 030=30 | F=Pharmaceutical grade | 05=5 10=10 20=20 30=30 40=40 | A=226 B=226 steel liner D=222 E=222 steel liner H=215 K=220 | P=Flat cap R="8" shape tail K=220 | S=Silicone E=EPDM V=Fluorelastomer |
Technical parameter of high precision polypropylene cartridge
Material | Series | Size code | Single/dual layer | Surface area (㎡)≥ | Pure water flow 0.2 μm ΔP=0.01MPa |
Polypropylene | Cartridge | F05 | Single layer | 0.2 | ≥5L/min |
F10 | Single layer | 0.4 | ≥10L/min | ||
F20 | Single layer | 0.8 | ≥20L/min | ||
F30 | Single layer | 1.2 | ≥30L/min | ||
F40 | Single layer | 1.6 | ≥40L/min |
Copyright © Shanghai Duoning Biotechnology Co., Ltd. All Rights Reserved Sitemap | Technical Support:
Message-